Mazda 6 Service Manual: Heated oxygen sensor (ho2s) inspection

Mazda 6 Service Manual / Fuel and emission control systems / Control system / Heated oxygen sensor (ho2s) inspection

HO2S Voltage Inspection

Note

Perform the following inspection only when directed.

1. Warm up the engine and run it at idle.

2. Disconnect the HO2S connector.

3. Connect the voltmeter test leads to the following HO2S terminals:

HO2S (front and rear)

- (+) leadterminal A

- (-) leadterminal B

4. With the vehicle stopped, run the engine at 3,000 rpm

until the voltmeter moves between 0.5 and 0.7 V.

5. Verify that the measurement voltage changes when the engine speed increases and decreases suddenly several times.

If not as specified, replace the HO2S.
If the HO2S is okay, but O2S11 or O2S12 PID value is out of specification, perform the Circuit Open/Short Inspection.

Specification

Circuit Open/Short Inspection (Sensor)

1. Disconnect the PCM connector. (See PCM REMOVAL/INSTALLATION.)

2. Inspect the following wiring harnesses for open or short. (Continuity check)

Open circuit

If there is no continuity, the circuit is open. Repair or replace the harness.

Front

- HO2S terminal A (harness-side) and PCM terminal 1AB (harness-side)

- HO2S terminal B (harness-side) and PCM terminal 2H (harness-side)

Rear

- HO2S terminal A (harness-side) and PCM terminal 1Y (harness-side)

- HO2S terminal B (harness-side) and PCM terminal 2H (harness-side)

Short circuit

If there is continuity, the circuit is shorted. Repair or replace the harness.

Front and Rear

- HO2S terminal A (harness-side) and body GND

- HO2S terminal A (harness-side) and power supply

- HO2S terminal B (harness-side) and power supply

HO2S Heater Resistance Inspection

1. Disconnect the HO2S connector.

2. Measure the resistance between the HO2S terminals C and D.

If not as specified, replace the HO2S.
If the HO2S heater is okay, but PID value is out of specification, perform the Circuit Open/Short Inspection.

Specification
Front : 3.0-3.6 ohms
Rear : 5-7 ohms

Circuit Open/Short Inspection (Heater)

1. Disconnect the PCM connector. (See PCM REMOVAL/INSTALLATION.)

2. Inspect the following wiring harnesses for open or short. (Continuity check)

Open circuit

If there is no continuity, the circuit is open. Repair or replace the harness.

Front

- HO2S terminal C (harness-side) and ignition switch

- HO2S terminal D (harness-side) and PCM terminal 4A (harness-side)

Rear

- HO2S terminal C (harness-side) and ignition switch

- HO2S terminal D (harness-side) and PCM terminal 4D (harness-side)

Short circuit

If there is no continuity, the circuit is shorted. Repair or replace the harness.

Front and rear

- HO2S terminal C (harness-side) and body GND

- HO2S terminal D (harness-side) and power supply

- HO2S terminal D (harness-side) and body GND

Knock sensor removal/installation

1. Remove the intake manifold. (See INTAKE-AIR SYSTEM REMOVAL/INSTALLATION.) 2. Remove the knock sensor attachment bolt to remove the knock sensor. 3. Install in the reverse order of removal. ...

Power steering pressure (psp) switchinspection

Note Perform the following inspection only when directed. Continuity Inspection 1. Inspect the following if the power steering is inoperative (See POWER STEERING FLUID INSPECTION.): Powe ...

Other materials:

Mazda 6 Service Manual: Trunk Lid
WARNING Never allow a person to ride in the trunk: Allowing a person to ride in the trunk is dangerous. The person in the trunk could be seriously injured or killed during sudden braking or a collision. Do not drive with the trunk lid open: Exhaust gas in the cabin of a vehicle is dangerous. ...

Mazda 6 Service Manual: Foreword
Caution When the engine does not start or stalls and the following DTCs are not indicated, go to engine symptom troubleshooting. Note When the immobilizer system is defective, the engine cannot be started. If engine condition is normal but light stays on, inspect for short circ ...