Mazda 6 Service Manual: Automatic transaxle
Mazda 6 Service Manual / Automatic transaxle
- Location index
- Automatic transaxle
- Mechanical system test
- Road test
- Automatic transaxle fluid (atf) inspection
- Automatic transaxle fluid (atf) replacement
- Hold switch inspection
- Hold switch removal/installation
- Transaxle range (tr) switch inspection
- Transaxle range (tr) switch removal/installation
- Transaxle range (tr) switch adjustment
- Transaxle fluid temperature (tft) sensor inspection
- Transaxle fluid temperature (tft) sensor removal/installation
- Oil pressure switch inspection
- Oil pressure switch removal/installation
- Input/turbine speed sensor inspection
- Input/turbine speed sensor removal/installation
- Vehicle speedometer sensor (vss) inspection
- Vehicle speedometer sensor (vss) removal/installation
- Solenoid valve inspection
- Solenoid valve removal/installation
- Pcm inspection
- Pcm removal/installation
- Automatic transaxle removal/installation
- Oil seal replacement
- Control valve body removal
- Control valve body installation
- Oil cooler flushing
- Oil cooler removal/installation
- Oil cooler disassembly/assembly
- Drive plate removal/installation
- Automatic transaxle shift mechanism
- Shift-lock inspection
- Key interlock inspection
- Interlock cable inspection
- Selector lever inspection
- Selector cable adjustment
- Selector lever removal/installation
- Selector lever disassembly/assembly
- On-board diagnostic
- Foreword
- Automatic transaxle on-board diagnostic function
- After repair procedure
- Dtc table
- Dtc p0500
- Dtc p0706
- Dtc p0707
- Dtc p0708
- Dtc p0711
- Dtc p0712
- Dtc p0713
- Dtc p0715
- Dtc p0731
- Dtc p0732
- Dtc p0733
- Dtc p0734
- Dtc p0741
- Dtc p0742
- Dtc p0745
- Dtc p0751
- Dtc p0752
- Dtc p0753
- Dtc p0756
- Dtc p0757
- Dtc p0758
- Dtc p0761
- Dtc p0762
- Dtc p0763
- Dtc p0766
- Dtc p0767
- Dtc p0768
- Dtc p0771
- Dtc p0772
- Dtc p0773
- Dtc p0841
- Pid/data monitor inspection
- Troubleshooting
- Foreword
- Basic inspection
- Symptom troubleshooting item table
- Quick diagnosis chart
- No.1 vehicle does not move in d, s, l ranges, or in r position
- No.2 vehicle moves in n position
- No.3 vehicle moves in p position, or parking gear does not disengage when p is disengaged
- No.4 excessive creep
- No.5 no creep at all
- No.6 low maximum speed and poor acceleration no.7 no shifting
- No.7 no shifting
- No.8 does not shift to fourth gear (4gr)
- No.9 abnormal shifting
- No.10 frequent shifting
- No.11 shift point is high or low
- No.12 torque converter clutch (tcc) non-operation
- No.13 no kickdown
- No.14 engine flares up or slips when upshifting or downshifting
- No.15 engine flares up or slips when accelerating vehicle
- No.16 judder upon torque converter clutch (tcc) operation
- No.17 excessive shift shock from n to d or n to r position/range
- No.18 excessive shift shock is felt when upshifting and downshifting
- No.19 excessive shift shock on torque converter clutch (tcc)
- No.20 noise occurs at idle when vehicle is stopped in all positions/ranges
- No.21 noise occurs at idle when vehicle is stopped in d, s, l ranges, or in r position
- No.22 no engine braking in hold mode
- No.23 transaxle overheats
- No.24 engine stalls when shifted to d, s, l ranges, or in r position
- No.25 engine stalls when driving at slow speeds or stopping
- No.26 starter does not work
- No.27 hold indicator light does not illuminate when hold switch is turned to on
- No.28 hold indicator light illuminates when hold switch is not turned to on
Shift mechanism
1. Remove the battery, battery tray and battery bracket.
2. Remove the air cleaner component. (See INTAKE-AIR SYSTEM
REMOVAL/INSTALLATION.)
3. Remove the dashboard compleat. (See DASHBOARD REMOVAL ...
Location index
AUTOMATIC TRANSAXLE LOCATION INDEX
...
Other materials:
Mazda 6 Service Manual: Clock spring adjustment
Note
The adjustment procedure is also specified on the caution label of
the clock spring.
1. Set the front wheels straight ahead.
Caution
The clock spring will break if over-wound. Do not forcibly turn
the clock spring.
2. Turn the clock spring clockwise until it stops.
3. Tu ...
Mazda 6 Service Manual: Climate control unit inspection
Full-auto Air Conditioner
1. Connect the all center panel connectors.
2. Turn the ignition switch to ON position.
3. Measure the voltage at each climate control unit terminal and refer to the
terminal voltage list.
If not as specified, inspect the parts listed under Action and the
relate ...
© 2016-2026 Copyright www.mazda6info.net