Mazda 6 Service Manual: Heater and air conditioner systems
Mazda 6 Service Manual / Heater and air conditioner systems
- Location index
- Service warnings
- Service cautions
- Refrigerant system service procedures
- Basic system
- Blower unit removal/installation
- Blower unit disassembly/assembly
- Air filter removal/installation
- Air filter inspection
- A/c unit removal/installation
- A/c unit disassembly/assembly
- Expansion valve removal/installation
- Evaporator inspection
- Heater core inspection
- Rear heat duct removal/installation
- A/c compressor removal/installation
- Condenser removal/installation
- Condenser inspection
- Refrigerant lines removal/installation
- Control system
- Air intake actuator removal/installation
- Air intake actuator inspection
- Air mix actuator removal/installation
- Air mix actuator inspection
- Airflow mode actuator removal/installation
- Airflow mode actuator inspection
- Blower motor removal/installation
- Blower motor inspection
- Resistor removal/installation
- Resistor inspection
- Power mos fet inspection
- Magnetic clutch disassembly/assembly
- Magnetic clutch adjustment
- Magnetic clutch inspection
- Solar radiation sensor removal/installation
- Solar radiation sensor inspection
- Ambient temperature sensor removal/installation
- Ambient temperature sensor inspection
- Cabin temperature sensor removal/installation
- Cabin temperature sensor inspection
- Evaporator temperature sensor removal/installation
- Evaporator temperature sensor inspection
- Water temperature sensor removal/installation
- Water temperature sensor inspection
- Refrigerant pressure switch removal/installation
- Refrigerant pressure switch inspection
- Climate control unit removal
- Climate control unit installation
- Climate control unit disassembly/assembly
- Climate control unit wire adjustment
- Climate control unit inspection
- Fan switch inspection
- Defroster switch inspection
- On-board diagnostic
- Diagnostic trouble code number inspection
- Dtc 02
- Dtc 06
- Dtc 07
- Dtc 10
- Dtc 11
- Dtc 12
- Dtc 13
- Dtc 14
- Dtc 15
- Dtc 18
- Dtc 19
- Dtc 21
- Dtc 22
- Dtc 58
- Dtc 59
- Dtc 02, 18, 21 (when two or more dtcs are indicated at the same time)
- Dtc 06, 10, 12, 14, 18, 21 (when two or more dtcs are indicated at the same time)
- Dtc 07, 11, 13, 15, 19, 22 (when two or more dtcs are indicated at the same time)
- Dtc 19, 22 (when two or more dtcs are indicated at the same time)
- Troubleshooting
- Foreword
- Troubleshooting index
- No.1 insufficient air (or no air) blown from vents
- No.2 amount of air blown from vents does not change
- No.3 amount of air blown from vents does not change
- No.4 air intake mode does not change
- No.5 no temperature control with climate control unit
- No.6 windshield fogged
- No.7 air from vents cold enough
- No.8 no cool air
- No.9 noise while operating a/c system
No.4 passenger-side air bag cut-off indicator light is illuminated all the
time
Diagnostic Procedure
When performing an asterisked (*) troubleshooting inspection, shake the
wiring harness and connectors while doing the inspection to discover whether
poor contact point ...
Location index
...
Other materials:
Mazda 6 Service Manual: Front upper arm removal/installation
Caution
Performing the following procedures without first removing the ABS
wheel-speed sensor may possibly cause an open circuit in the harness if it
is pulled by mistake. Before performing the following procedures, remove the
ABS wheel-sensor (axle side) and fix it to an appropriate pl ...
Mazda 6 Service Manual: Neutral switch inspection
Note
Perform the following inspection only when directed.
Continuity Inspection
1. Disconnect the negative battery cable.
2. Remove the neutral switch.J5 MANUAL TRANSAXLE REMOVAL/INSTALLATION.)
3. Inspect for continuity between the neutral switch terminals using an
ohmmeter.
If the n ...
© 2016-2026 Copyright www.mazda6info.net