Mazda 6 Service Manual
Mazda 6 Service Manual
- General information
- How to use this manual
- Units
- Fundamental procedures
- Installation of radio system
- Electrical system
- Jacking positions ,vehicle lift (2 supports),safety stands (rigid rack) positions
- Towing
- Identification number locations
- New standards
- Abbreviations
- Pre-delivery inspection
- Scheduled maintenance
- Engine
- Mechanical location index
- Drive belt
- Valve clearance
- Compression pressure
- Timing chain
- Cylinder head gasket
- Front oil seal
- Rear oil seal
- Engine
- Variable valve timing
- Oil control valve (ocv)
- Lubrication system
- Cooling system
- Location index
- Cooling system service warnings
- Engine coolant
- Radiator cap
- Radiator
- Thermostat
- Water pump
- Fan motor
- Fuel and emission control systems
- Location index
- Engine tune-up
- Intake-air system
- Fuel system
- Exhaust system
- Emission system
- Control system
- On-board diagnostic
- Troubleshooting
- Engine electrical system
- Clutch
- Location index
- General procedures
- Clutch fluid
- Clutch pedal
- Clutch master cylinder
- Clutch release cylinder
- Clutch unit
- Flywheel
- Manual transaxle
- Automatic transaxle
- Location index
- Automatic transaxle
- Automatic transaxle shift mechanism
- On-board diagnostic
- Troubleshooting
- Front and rear axles
- Steering system
- Braking system
- Location index
- General procedures
- Conventional brake system
- Parking brake system
- Abs/tcs
- Dynamic stability control
- On-board diagnostic (abs/tcs)
- On-board diagnostic (dynamic stability control)
- Troubleshooting (abs/tcs/dynamic stability control)
- Suspension
- Body
- Location index
- Bonnet
- Front fender panel
- Door
- Power window system
- Power door lock system
- Trunk lid
- Liftgate
- Fuel-filler lid and opener
- Bumper
- Exterior attachment
- Molding
- Outside mirror
- Rearview mirror
- Rear window defroster
- Window glass
- Sliding sunroof
- Dashboard and console
- Trim
- Headliner
- Floor covering
- Seat belt
- Seat
- Body shell
- Troubleshooting [power window system]
- Troubleshooting [keyless entry system]
- Body electrical system
- Location index
- Power system
- Exterior lighting system
- Interior lighting system
- Wiper and washer
- Warning and indicator system
- Theft-deterrent system
- Immobilizer system
- Audio and navigation system
- Cruise control system
- Air bag system
- On-board diagnostic [multiplex communication system]
- On-board diagnostic [headlight auto leveling system]
- On-board diagnostic [immobilizer system]
- On-board diagnostic [audio]
- On-board diagnostic [cruise control system]
- On-board diagnostic [air bag system]
- Troubleshooting
- Heater and air conditioner systems
- Location index
- Service warnings
- Service cautions
- Refrigerant system service procedures
- Basic system
- Control system
- On-board diagnostic
- Troubleshooting
- Technical data
- Special tools
Personalization Features
The following personalization features can be set or changed by the customer
or an Authorized Mazda Dealer. Consult an Authorized Mazda Dealer for details.
Additionally, some of the personalization ...
Other materials:
: Climate control unit removal
1. Disconnect the negative battery cable.
2. Disconnect the air mix and airflow mode wires from each wire clamp and
link. (Manual air conditioner)
3. Remove the center panel. (See CENTER PANEL MODULE REMOVAL/INSTALLATION.)
4. Remove the screws and climate control unit. (Full-auto air conditione ...
: Roof molding installation
1. Attach the roof molding to the T stud at the A section.
2. Press in the roof molding along the direction (1) shown in the figure and
attach it to the clip A at the B section.
3. Hook the roof molding to the clip B at the C section, press it in, and
attach the roof molding to the clip B.
...
© 2016-2026 Copyright www.mazda6info.net